#6.2 2.4 packet tracer software
#6.2 2.4 packet tracer download

#6.2 2.4 packet tracer download

Students can download the program for free, and use the simulation to confirm ideas, concepts, and practical knowledge. Developed by Cisco Systems as part of the Networking Academy, itвЂ™s a comprehensive, multi-faceted tool.

#6.2 2.4 packet tracer software

The three questions in Step 1, 2 and 4 are worth 20 points.Visual simulation software for young aspirants!Д¬isco Packet Tracer is one of the most popular system software for simulating network configurations. Why is port G0/1 on S2 no longer assigned to VLAN 1? Port G0/1 is a trunk port and trunks ports are not displayed. Use the show vlan command to display information regarding configured VLANs.

Issue the show interface interface switchport command to verify that the native VLAN is now 99.Step 4: Verify configurations on S2 and S3. Issue show interface trunk command to verify the correct native VLAN configuration.Configure VLAN 99 as the native VLAN for the appropriate interfaces on S2 and S3.Step 3: Correct the native VLAN mismatch on S2 and S3. Which active VLANs are allowed to cross the trunk? 1, 10, 20, 30, and 99. The output also displays information about the trunk interfaces on S2 and S3. On S2 and S3, issue the show interface trunk command to confirm that DTP has successfully negotiated trunking with S1 on S2 and S3. Step 2: Verify trunking is enabled on S2 and S3. In this case, S2 and S3 have now automatically configured the ports attached to S1 as trunking ports. Dynamic Trunking Protocol (DTP) has automatically negotiated the other side of the trunk links. Why? Pings are successful because trunking has been enabled on S1. Although you have a native VLAN mismatch, pings between PCs on the same VLAN are now successful.However, S2 and S3 are using VLAN 1 as the default native VLAN as indicated by the syslog message. You configured VLAN 99 as the native VLAN on S1.%CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered on GigabitEthernet0/1 (99), with S2 GigabitEthernet0/1 (1).%CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered on GigabitEthernet0/2 (99), with S3 GigabitEthernet0/2 (1).After the ports become active, you will periodically receive the following syslog messages:

Click Fast Forward Time to speed the process.

The trunk port takes about a minute to become active due to Spanning Tree.

S1(config-if)# switchport trunk native vlan 99.

Configure VLAN 99 as the native VLAN for G0/1 and G0/2 interfaces on S1.

Configure G0/1 and G0/2 interfaces on S1 for trunking.

Part 2: Configure Trunks Step 1: Configure trunking on S1 and use VLAN 99 as the native VLAN. In order to provide connectivity between the PCs on the same network and VLAN, trunks must be configured. This is because the ports connecting the switches are assigned to VLAN 1 by default. Step 2: Verify loss of connectivity between PCs on the same network.ДЄlthough PC1 and PC4 are on the same network, they cannot ping one another.

On S2 and S3, display and verify all the VLANs are configured and assigned to the correct switch ports according to the Addressing Table.

Notice how all 24 access ports on the switch are assigned to VLAN 1.

On S1, issue the command that will display all VLANs configured.

Part 1: Verify VLANs Step 1: Display the current VLANs.

This activity focuses on creating trunk ports, and assigning them to a native VLAN other than the default. A trunk port by default is a member of all VLANs therefore, it carries traffic for all VLANs. Access ports carry traffic from a specific VLAN assigned to the port. A port on a switch is either an access port or a trunk port. Trunks are required to pass VLAN information between switches. 6.2.2.4 Packet Tracer вЂ“ Configuring Trunks Addressing Table Device